What Is EOR, and How Does It Work?

Enhancing Oil Recovery




Enhancing Oil Recovery
Enhancing Oil Recovery

Oil production is separated into three phases: primary, secondary and tertiary, which is also known as Enhanced Oil Recovery (EOR). Primary oil recovery is limited to hydrocarbons that naturally rise to the surface, or those that use artificial lift devices, such as pump jacks. Secondary recovery employs water and gas injection, displacing the oil and driving it to the surface. According to the US Department of Energy, utilizing these two methods of production can leave up to 75% of the oil in the well.
The way to further increase oil production is through the tertiary recovery method or EOR. Although more expensive to employ on a field, EOR can increase production from a well to up to 75% recovery.
Used in fields that exhibit heavy oil, poor permeability and irregular faultlines, EOR entails changing the actual properties of the hydrocarbons, which further distinguishes this phase of recovery from the secondary recovery method. While waterflooding and gas injection during the secondary recovery method are used to push the oil through the well, EOR applies steam or gas to change the makeup of the reservoir.
Whether it is used after both primary and secondary recovery have been exhausted or at the initial stage of production, EOR restores formation pressure and enhances oil displacement in the reservoir.
There are three main types of EOR, including chemical flooding, gas injection and thermal recovery. Increasing the cost of development alongside the hydrocarbons brought to the surface, producers do not use EOR on all wells and reservoirs. The economics of the development equation must make sense. Therefore, each field must be heavily evaluated to determine which type of EOR will work best on the reservoir. This is done through reservoir characterization, screening, scoping, and reservoir modeling and simulation.



Thermal Recovery

Thermal recovery introduces heat to the reservoir to reduce the viscosity of the oil. Many times, steam is applied to the reservoir, thinning the oil and enhancing its ability to flow. First applied in Venezuela in the 1960s, thermal recovery now accounts for more than 50% of applied EOR in the US.


Thermal Recovery
Thermal Recovery


Chemical Injection

Chemical injection EOR helps to free trapped oil within the reservoir. This method introduces long-chained molecules called polymers into the reservoir to increase the efficiency of waterflooding or to boost the effectiveness of surfactants, which are cleansers that help lower surface tension that inhibits the flow of oil through the reservoir. Less than 1% of all EOR methods presently utilized in the US consist of chemical injections.


Gas Injection

Gas injection used as a tertiary method of recovery involves injecting natural gas, nitrogen or carbon dioxide into the reservoir. The gases can either expand and push gases through the reservoir, or mix with or dissolve within the oil, decreasing viscosity and increasing flow.


Gas injection
Gas injection



Carbon Dioxide EOR

Carbon dioxide EOR (CO2-EOR) is the method that is gaining the most popularity. While initial CO2-EOR developments used naturally occurring carbon dioxide deposits, technologies have been developed to inject CO2 created as byproducts from industrial purposes.
First employed in the US in the early 1970s in Texas, CO2-EOR is successfully used in Texas and New Mexico and is expected to become more widely spread in the future. Nearly half of the EOR employed in the US is a form of gas injection.
Other EOR applications gaining acceptance are low-salinity water flooding, which is expected to increase production by nearly 20%, and well stimulation, which is a relatively low-cost solution because it can be employed to single wells (rather than the whole reservoir).


keywords: EOR, recovery, chemical, injection.

Comments

Post a Comment

Popular posts from this blog

Gas-Lift Troubleshooting

Image
Troubleshoot your well before you call a rig. Gas-lift problems are usually associated with three areas: inlet, outlet, and downhole (Fig. 1). Examples of inlet problems may be the input choke sized too large or too small, fluctuating line pressure, plugged choke, etc. Outlet problems could be high backpressure because of a flowline choke, a closed or partially closed wing or master valve, or a plugged flowline. Downhole problems could include a cutout valve, restrictions in the tubing string, or sand-covered perforations. Further examples of each problem area are included in this handbook. Often the problem can be found Fig. 1: The Gas-Lift System on the surface. If nothing is found on the surface, a check can then be made to determine whether the downhole problems are wellbore problems or equipment problems. Inlet Problems Choke sized too large .  Check for casing pressure at or above design operating pressure. This can cause reopening of upper-pressure valves and/or
Read more

Permeability of oil-gas Reservoir Rock

Image
 Permeability of Petroleum Reservoir Rock In addition to being porous, a reservoir rock must be permeable—that is, it must allow fluids to flow through its pore network at practical rates under reasonable pressure differentials. Permeability is defined as: 1.              The ability of a formation to transmit fluids 2.              The ability of rocks to allow the circulation of fluids contained in their pores. 3.              The ability of the rock to allow a fluid with which it is saturated to flow through its pores . Permeability is a measure of the ease with which the fluid flows in the porous medium. Figure 4.1 represents a schematic showing the difference between low and high permeability rocks in a reservoir. The permeability of a rock measured when it is 100% saturated with a single phase (water, oil, or gas) is often called “ single-phase permeability ”, “ absolute permeability ,” or just “ permeability ”. If there are two fluids flowing in a rock, then it rela
Read more

Equilibrium Separation

Image
  Characteristics of Oil and Gas Equilibrium Separation Low Shrinkage Oils A given volume of oil existing at its bubble point at reservoir temperature is considered to be saturated with gas at the given temperature and pressure conditions. Thus, the term "saturation pressure" is synonymous with bubble-point pressure at a given temperature. A decrease in pressure will cause the original sample to change into two phases as shown in the next figure. The physical change is evidenced as gas being liberated from the liquid. It is a common misbelief that a certain amount of gas is dissolved in oil and that a pressure drop results in the gas coming out of solution. Actually, the first gas liberated is composed principally of the lightest components (methane, ethane and propane) because these components possess the highest molecular energy and the lowest molecular attraction for other molecules. Equilibrium vaporization of low shrinkage oil. Vaporization of the lighter components is u
Read more